Gas Path Analysis on the GEnx-1B at KLM Engine Services

Gas Path Analysis on the GEnx-1B at KLM Engine Services

van Moorselaar, Martijn (TU Delft Aerospace Engineering)

Visser, W.P.J. (mentor)

Delft University of Technology

Aerospace Engineering

2018-09-24

Modern gas turbines are complex and expensive machines, requiring specialised maintenance to keep them in working order. Maintenance takes places at specialised shops such as KLM Engine Services (KLM ES). Part of KLM Engineering & Maintenance (KLM E&M), KLM ES provides maintenance ser- vices to aircraft engines belonging both to KLM and to external customers. Gas Path Analysis (GPA) is a technique which can aid KLM ES in its maintenance process. As a gas turbine deteriorates over time, its performance will change. These changes in performance can be measured in the gas path of the engine. Using GPA the degraded component can be identified, after which corrective steps can be taken. This analysis gives more insight into the condition of a gas turbine than the traditional method in which only the Exhaust Gas Temperature (EGT) margin is taken into account. At KLM ES GPA is performed using Gas turbine Simulation Program (GSP), currently with the capability to analyse the General Electric (GE) CF6-80 and CFMI CFM56-7B. Recently KLM ES has started maintenance on the GE GEnx-1B, powering the Boeing 787. The GEnx-1B is a state of the art aircraft engine, capable of collecting large amounts of performance data while in operation. KLM ES is not yet able to apply GPA to the GEnx-1B. The objective of this research is to extend the use of GPA at KLM ES to the GEnx-1B, by creating a model in GSP capable of providing accurate GPA results for the GEnx-1B using both test cell and on-wing measurements. A GSP model has been created based on test cell measurements, taken at different power settings, of an average GEnx-1B. The range of power settings over which the model is capable of simulating the engine has been extended using take-off snapshots taken on-wing. Off-design performance simulation in GSP is based on component maps, describing the performance of the compressors and turbines of a gas turbine. Component maps describing the behaviour of the GEnx-1B components are proprietary to GE and unavailable in the public domain. Therefore maps representing a CF6-80, which are based on publicly available maps and are accessible at KLM ES, have been tuned to match the measured GEnx- 1B performance. The tuned model is capable of simulating the reference engine in take-off conditions well. Some modelling errors remain, however these do not hamper the usability of the model of GPA. Although the GEnx-1B is a much more modern engine than a CF6-80, it has fewer sensors installed in its gas path. Most importantly no pressure measurement is taken in the fan bypass, after the booster and after the High Pressure Turbine (HPT). During modelling this increased the uncertainty involved in tuning the component maps and required additional assumptions to be made to fix the model in the design point. Furthermore it has its effect on the application of GPA using GSP. The GPA method implemented in GSP is Adaptive Modelling (AM). AM is directly dependent on the amount of parameters measured in an engine, it requires an equal amount of available measurements as engine parameters it can adapt to compute an engine its condition. As previous work focused on engines with more measurements available, more research was required to investigate the possibility of applying AM to the GEnx-1B. It is found that the lack of a pressure sensor after the HPT affects GPA the most. With this sensor missing, deterioration on the Low Pressure Turbine (LPT) is contributed to an HPT efficiency loss by the AM component. Having no pressure measurement after the booster does not severely impact AM results. Lack of a thrust measurement, or equivalent pressure measurement, results in having no information available on the fan when on-wing snapshots are analysed. Overall it was concluded that the model would still be usable to analyse the condition of GEnx-1Bs in operation, or in the test cell after maintenance. The model has been tested using snapshots of test cell measurements available from multiple engines and using on-wing take-off snapshots of the whole KLM fleet. Results based on test cell snapshots correlate well with the work done during the shopvisits and with the EGT margin as reported by the test cell software. Analysis of on-wing snapshots also shows a good relation with the EGT margin as computed by the engine. Furthermore deterioration is attributed to the components on which it would be expected. On-wing results are affected by scatter, which also influences the choice of reference dataset. A suggestion is made for a reference dataset, enabling the analysis of all KLM GEnx-1Bs considered. Overall it is proved that it is possible to analyse a modern engine such as the GEnx-1B with GSP, both in the test cell and in operation.

http://resolver.tudelft.nl/uuid:51b66a01-a485-4aac-a6e6-544f619b9aa1

Student theses

master thesis

© 2018 Martijn van Moorselaar