Determining the speed of sound in curved bones

Determining the speed of sound in curved bones

Vermeulen, Mark (TU Delft Applied Sciences; TU Delft Electrical Engineering, Mathematics and Computer Science)

Vuik, Cornelis (mentor)
Verweij, M.D. (graduation committee)
Dubbeldam, J.L.A. (graduation committee)
Verschuur, D.J. (graduation committee)
Mozaffarzadeh, M. (graduation committee)
de Jong, N. (graduation committee)

Delft University of Technology

Applied Physics

2022-02-24

Current research on osteoporosis detection and transcranial imaging suggests that it is necessary to find a method to calculate the speed of sound in curved bones. A popular method to find the speed of sound in bones is by the bidirectional axial transmission technique. Currently, this method assumes that the arrival time of the head wave depends linearly on the source-receiver distance. For curved bones this assumption is not valid. The arrival time of the head wave as a function of the source-receiver distance follows a curved trajectory. In this report, we attempt to find an extension to the current method that also works for curved bones, and evaluate how accurate the results of this extended method are.

This extension is based on the semblance method, that quantifies how well a certain trajectory agrees with the received data. In the first part of our project, theoretical trajectories are calculated for flat and semicircular bones. Furthermore, a numerical method is discussed to find these trajectories for arbitrary geometries. Comparing the trajectories corresponding to different velocities using the semblance methods allows for the determination of the speed of sound.

The accuracy of this extended method is evaluated by computer simulations. In these simulations, a Philips P41 Cardiac Sector Probe consisting of 96 elements was used to perform measurements on three different geometries. These geometries consisted of three different single interfaces between water (simulating soft tissue) and bone. The first interface consists of a straight interface between a 2 mm thick layer of water and a 5 mm thick layer of bone (that continues until the bottom edge of the simulation). The second simulation is the same, but the interface is rotated 2 degrees around its midpoint. In the third and fourth simulation, the interface is a semicircle with a 50 mm and 40 mm radius, respectively. The speed of sound in the bone was taken to be 3 mm/𝜇s. The received data was interpolated by a cubic interpolation with a refinement of 4. Both the bidirectional and the extended,
trajectory-based method were applied on the raw and interpolated data.

For the flat interface, the bidirectional method performed slightly better than the trajectory-based method (0.13% and 0.30% error, respectively). The same is true for the tilted interface (0.16% and 0.23% error). Interpolation did not affect the results here. For the 50 mm semicircular interface, the trajectory-based method performed much better than the bidirectional method: it had a 0.10% error compared to a 2% one. This was also true when the interpolation was applied: then the errors were 0.3% and 1.97%. Similar
improvements were seen for the 40 mm radius semicircle. The higher error of the trajectory-based method for the flat and tilted interfaces can be explained by small errors in the additional assumptions that this method makes.

One drawback of the trajectory-based method is that there can be problems interpreting the results. This can be seen in the semblance plots, which plot the semblance coefficient (how well the trajectory fits the data) against the test velocity. For the bidirectional method, these plots clearly have a single biggest peak. For the trajectory-based methods the plot contains multiple large peaks. Furthermore, for the semicircular bone this plot contains a flat peak, which can cause multiple test velocities to have approximately the same semblance. This is a problem, since it means that small changes to the experimental setup can cause big changes in the calculated velocity. Indeed, this can be seen for the trajectory-based method on the 40 mm radius semicircular bone, which has a 1.6% error without interpolation (0.43% with interpolation). Further research could examine solutions to this problem, such as increasing the window size of the semblance method, taking the average velocity over flat peaks, or using an alternative to the semblance method. Finally, we conclude that the trajectory-based method represents an improvement over the bidirectional method when examining curved bones.

head wave
ultrasound
osteoporosis
imaging

http://resolver.tudelft.nl/uuid:e371413d-ac37-4fc8-aa24-0edd46d00ce0

Student theses

bachelor thesis

© 2022 Mark Vermeulen